Car radio for VW Bulli T2 with DAB+, station buttons, ivory, Retrosound San Diego

The new "San Diego" is RetroSound's first car radio with DAB+, Bluetooth hands-free calling, A2DP audio streaming, and Apple iPod/iPhone control. With this single unit, you get the classic design of your VW Bus without sacrificing modern digital media. Two USB and two AUX inputs allow you to connect external MP3 storage devices such as an iPhone, iPod, or USB flash drive.

The radio comes complete with a mounting bezel and knob set for your VW Bus T2 (1967–1979).
Any concerns that installing a RetroSound car radio might jeopardize your historic vehicle registration are unfounded. There is confirmation, with the approval of the entire AKE working group (TÜV SÜD, TÜV Rheinland, TÜV Nord, Dekra, KÜS, GTÜ), stating that the RetroSound "Model Hermosa", "Model Classic" and the RetroSound "San Diego", including vehicle-specific trim and control knobs, may be installed in classic cars with H-plates and will not prevent the issuance of an H-plate!

Features:
- Playback of MP3 and WMA files via two rear-mounted USB inputs
- Apple iPod/iPhone control
- Bluetooth hands-free system with A2DP audio streaming
- Adjustable LCD backlighting with 32,000 different colors
- FM/AM radio receiver with RDS and 30 station presets
- Switchable radio frequencies (USA/EUROPE)
- New control system with control knobs and Ring functionality
- Integrated 4-channel amplifier (4 x 24 watts RMS / 45 watts max.)
- Three pairs of RCA outputs for external amplifiers
- Patented "InfiniMount" mounting system and control knobs
- 3 equalizer programs plus individual bass/treble/fader/balance adjustments
- E-approval e13 03 10006 e13*72/245*2006/96*10006*00
- XBAS loudness function
- Separate power leads for motorized antenna and amplifier
- Auto reset to factory settings after 5 minutes without power
- The radio is supplied with plastic control knobs. Some of the control knob variations are available in metal and can be purchased separately.

Technical Specifications:
FM
- European Broadcast frequency range with RDS 87.5-107.9
- External antenna connection
- Sensitivity 12.5 dBf
- Station separation 75 dB at 400 kHz
- Signal-to-noise ratio 62 dB
- Distortion at 1 kHz 0.8% (stereo) 0.5% (mono)
- Channel separation 32 dB at 1 kHz
- Frequency response 30-16000 Hz
MW
- Frequency range 530-1710 kHz
- External antenna connection
DAB+
- External SMB antenna input

IPOD/IPHONE COMPATIBILITY
- iPhone 5 to XS (Lightning USB cable required)
- iPhone 3G to 4s (30-pin USB cable required)
- iPod touch 2G to 3G (30-pin USB cable required)
- iPod nano 3G to 6G (30-pin USB cable required)
- iPod classic 80-160GB (30-pin USB cable required)

General Data:
- Control unit dimensions: 89 x 38 x 27 mm
- Radio unit dimensions: 101 x 51 x 136 mm
- Power supply: 10.5 to 14.4 volts
- Maximum current draw: 15 amps
- Standby current: 3.5 mA
- Output power: 12V, 4 ohms <1% THD: 4x15 Watts RMS
- Speaker Impedance 4-8 Ohms
- RCA Outputs 4 Channel 2.85 Volts
- Input Sensitivity Aux1, Aux2 >300 mV / 6 kOhms

LEGAL NOTICE
iPod and iPhone are trademarks of Apple Computer, registered in the U.S. and other countries. For best results, Apple has established certain compatibility requirements for accessory manufacturers. Products designed and certified to be compatible will have the "Made for" marking on their packaging. To ensure compatibility when purchasing third-party accessories for use with your device, look for accessories labeled "Made for" your device (see below). "Made for iPod" means that an electronic accessory is specifically designed for connection to the iPod and has been certified by the developer to meet Apple performance standards. "Made for iPhone" means that an electronic accessory is specifically designed for connection to the iPhone and has been certified by the developer to meet Apple performance standards. 6-Volt Electrical Systems: You will need a voltage converter if you wish to operate a RetroSound car radio in a vehicle with a 6-volt electrical system. We recommend the Statron 2238.0 DC/DC converter (www.statron.de) in such a case.

E-APPROVAL
- E-approval e13 03 10006 e13*72/245*2006/96*10006*00